Class 12 Chemistry - Chapter Solutions NCERT Solutions | H2S, a toxic gas with rotten egg like sm

A 5% solution (by mass) of cane sugar in water has freezing point of 271 K. Calculate the freezing point of 5% glucose in water if freezing point of pure water is 273.15 K.

A solution of glucose in water is labelled as 10% w/w, what would be the molality and mole fraction of each component in the solution? If the density of solution is 1.2 g mL^-1, then what shall be the molarity of the solution?

Henry's law constant for CO₂ in water is 1.67 x 10⁸Pa at 298 K. Calculate the quantity of CO₂in 500 mL of soda water when packed under 2.5 atm CO₂ pressure at 298 K.

Calculate the mass of a non-volatile solute (molar mass 40 g mol^-1) which should be dissolved in 114 g octane to reduce its vapour pressure to 80%.

The vapour pressure of pure liquids A and B are 450 and 700 mm Hg respectively, at 350 K. Find out the composition of the liquid mixture if total vapour pressure is 600 mm Hg. Also find the composition of the vapour phase.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

How many mL of 0.1 M HCl are required to react completely with 1 g mixture of Na₂CO₃ and NaHCO₃ containing equimolar amounts of both?

Boiling point of water at 750 mm Hg is 99.63°C. How much sucrose is to be added to 500 g of water such that it boils at 100°C.Molal elevation constant for water is 0.52 K kg mol^-1.

An aqueous solution of 2% non-volatile solute exerts a pressure of 1.004 bar at the normal boiling point of the solvent. What is the molar mass of the solute?

Vapour pressure of pure water at 298 K is 23.8 mm Hg. 50 g of urea (NH₂CONH₂) is dissolved in 850 g of water. Calculate the vapour pressure of water for this solution and its relative lowering.

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

How is dacron obtained from ethylene glycol and terephthalic acid?

What is a biodegradable polymer? Give an example of a biodegradable aliphatic polyester.

Classify the following as addition and condensation polymers: Terylene, Bakelite, Polyvinyl chloride, Polythene.

The time required for 10% completion of a first order reaction at 298 K is equal to that required for its 25% completion at 308 K. If the value of A is 4 x 10¹⁰ s^-1. Calculate k at 318 K and E_a.

What are polymers?

Give plausible explanation for each of the following:

(i) Cyclohexanone forms cyanohydrin in good yield but 2, 2, 6 trimethylcyclohexanone does not.

(ii) There are two -NH₂ groups in semicarbazide. However, only one is involved in the formation of semicarbazones.

(iii) During the preparation of esters from a carboxylic acid and an alcohol in the presence of an acid catalyst, the water or the ester should be removed as soon as it is formed.

Define thermoplastics and thermosetting polymers with two examples of each.

Which is the last element in the series of the actinoids? Write the electronic configuration of this element. Comment on the possible oxidation state of this element.

Write the chemistry of recharging the lead storage battery, highlighting all the materials that are involved during recharging.

Which meatal in the first series of transition metals exhibits +1 oxidationstate most frequently and why?