Class 12 Chemistry - Chapter Solutions NCERT Solutions | A solution is obtained by mixing 300 g o

A 5% solution (by mass) of cane sugar in water has freezing point of 271 K. Calculate the freezing point of 5% glucose in water if freezing point of pure water is 273.15 K.

A solution of glucose in water is labelled as 10% w/w, what would be the molality and mole fraction of each component in the solution? If the density of solution is 1.2 g mL^-1, then what shall be the molarity of the solution?

Henry's law constant for CO₂ in water is 1.67 x 10⁸Pa at 298 K. Calculate the quantity of CO₂in 500 mL of soda water when packed under 2.5 atm CO₂ pressure at 298 K.

Calculate the mass of a non-volatile solute (molar mass 40 g mol^-1) which should be dissolved in 114 g octane to reduce its vapour pressure to 80%.

The vapour pressure of pure liquids A and B are 450 and 700 mm Hg respectively, at 350 K. Find out the composition of the liquid mixture if total vapour pressure is 600 mm Hg. Also find the composition of the vapour phase.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

How many mL of 0.1 M HCl are required to react completely with 1 g mixture of Na₂CO₃ and NaHCO₃ containing equimolar amounts of both?

H₂S, a toxic gas with rotten egg like smell, is used for the qualitative analysis. If the solubility of H₂S in water at STP is 0.195 m, calculate Henry's law constant.

An aqueous solution of 2% non-volatile solute exerts a pressure of 1.004 bar at the normal boiling point of the solvent. What is the molar mass of the solute?

Boiling point of water at 750 mm Hg is 99.63°C. How much sucrose is to be added to 500 g of water such that it boils at 100°C.Molal elevation constant for water is 0.52 K kg mol^-1.

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

Why copper matte is put in silica lined converter?

Amongst the following, the most stable complex is

(i) [Fe(H₂O)₆]³⁺

(ii) [Fe(NH₃)₆]³⁺

(iii) [Fe(C₂O₄)₃]^3-

(iv) [FeCl₆]^3-

How will you convert?

(i) Benzene into aniline

(ii) Benzene into N, N-dimethylaniline

(iii) Cl-(CH₂)₄-Cl into hexan-1, 6-diamine?

Using IUPAC norms write the systematic names of the following:

(i) [Co(NH₃)6]Cl₃

(ii) [Pt(NH₃)₂Cl(NH₂CH₃)]Cl

(iii) [Ti(H₂O)6]³⁺

(iv) [Co(NH₃)₄Cl(NO₂)]Cl

(v) [Mn(H₂O)6]²⁺

(vi) [NiCl₄]^2-

(vii) [Ni(NH₃)₆]Cl₂

(viii) [Co(en)₃]³⁺

(ix) [Ni(CO)₄]

What is crystal field splitting energy? How does the magnitude of Δ_o decide the actual configuration of d-orbitals in a coordination entity?

For a first order reaction, show that time required for 99% completion is twice the time required for the completion of 90% of reaction.

Distinguish between the terms homopolymer and copolymer and give an example of each.

Explain:   (i) Zone refining    (ii) Column chromatography.

What is the coordination entity formed when excess of aqueous KCN is added to an aqueous solution of copper sulphate? Why is it that no precipitate of copper sulphide is obtained when H₂S(g) is passed through this solution?

State the role of silica in the metallurgy of copper.