Class 12 Chemistry - Chapter Polymers NCERT Solutions | Identify the monomer in the following po

Write the names and structures of the monomers of the following polymers:

(i) Buna-S  (ii) Buna-N

(iii) Dacron  (iv) Neoprene

What is a biodegradable polymer? Give an example of a biodegradable aliphatic polyester.

Arrange the following polymers in increasing order of their intermolecular forces.
(i) Nylon 6, 6, Buna-S, Polythene.
(ii) Nylon 6, Neoprene, Polyvinyl chloride.

Explain the difference between Buna-N and Buna-S.

How are polymers classified on the basis of structure?

Define thermoplastics and thermosetting polymers with two examples of each.

Explain the term copolymerisation and give two examples.

Write the monomers used for getting the following polymers. (i) Polyvinyl chloride (ii) Teflon (iii) Bakelite

How do you explain the functionality of a monomer?

What are the monomeric repeating units of Nylon-6 and Nylon-6, 6?

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

In the following pairs of halogen compounds, which compound undergoes faster S_N1 reaction?

Heptane and octane form an ideal solution. At 373 K, the vapour pressures of the two liquid components are 105.2 kPa and 46.8 kPa respectively. What will be the vapour pressure of a mixture of 26.0 g of heptane and 35 g of octane?

For the reaction:

2A + B → A₂B

the rate = k[A][B]²with k= 2.0 x 10^-6mol^-2L²s^-1. Calculate the initial rate of the reaction when [A] = 0.1 mol L^-1, [B] = 0.2 mol L^-1. Calculate the rate of reaction after [A] is reduced to 0.06 mol L^-1.

Why is zinc not extracted from zinc oxide through reduction using CO?

In a reaction, 2A → Products, the concentration of A decreases from 0.5 mol L^-1 to 0.4 mol L^-1 in 10 minutes. Calculate the rate during this interval?

Write the equations for the preparation of 1-iodobutane from

(i) 1-butanol

(ii) 1-chlorobutane

(iii) but-1-ene.

How are colloids classified on the basis of

(i) Physical states of components

(ii) Nature of dispersion medium and

(iii) Interaction between dispersed phase and dispersion medium?

A solution containing 30 g of non-volatile solute exactly in 90 g of water has a vapour pressure of 2.8 kPa at 298 K. Further, 18 g of water is then added to the solution and the new vapour pressure becomes 2.9 kPa at 298 K. Calculate:

1) Molar mass of the solute

2) Vapour pressure of water at 298 K.

Why are Mn²⁺compounds more stable than Fe²⁺ towards oxidation to their +3 state?

Define the following terms:

(i) Mole fraction    (ii) Molality    (iii) Molarity   (iv) Mass percentage.