Class 12 Chemistry - Chapter Chemical Kinetics NCERT Solutions | In a reaction, 2A → Products, the c

The half-life for radioactive decay of ¹⁴C is 5730 years. An archaeological artifact containing wood had only 80% of the ¹⁴C found in a living tree. Estimate the age of the sample.

For a first order reaction, show that time required for 99% completion is twice the time required for the completion of 90% of reaction.

The rate of a reaction quadruples when the temperature changes from 293 K to 313 K. Calculate the energy of activation of the reaction assuming that it does not change with temperature.

A first order reaction takes 40 min for 30% decomposition. Calculate t_1/2.

The conversion of molecules X to Y follows second order kinetics. If concentration of X is increased to three times how will it affect the rate of formation of Y?

During nuclear explosion, one of the products is ⁹⁰Sr with half-life of 28.1 years. If 1μg of ⁹⁰Sr was absorbed in the bones of a newly born baby instead of calcium, how much of it will remain after 10 years and 60 years if it is not lost metabolically.

Sucrose decomposes in acid solution into glucose and fructose according to the first order rate law, with t_1/2 = 3.00 hours. What fraction of sample of sucrose remains after 8 hours?

The decomposition of A into product has value of k as 4.5 x 10³ s^-1 at 10°C and energy of activation 60 kJ mol^-1. At what temperature would k be 1.5 x 10⁴ s^-1?

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

The following data were obtained during the first order thermal decomposition of SO₂Cl₂at a constant volume.

SO₂Cl₂₍g)  →  SO₂₍g) + Cl₂(g)

Calculate the rate of the reaction when total pressure is 0.65 atm.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

Write structures of the following compounds:

(i) 2-Chloro-3-methylpentane

(ii) 1-Chloro-4-ethylcyclohexane

(iii) 4-tert. Butyl-3-iodoheptane

(iv) 1,4-Dibromobut-2-ene

(v) 1-Bromo-4-sec. butyl-2-methylbenzene

Write the equations for the preparation of 1-iodobutane from

(i) 1-butanol

(ii) 1-chlorobutane

(iii) but-1-ene.

How are colloids classified on the basis of

(i) Physical states of components

(ii) Nature of dispersion medium and

(iii) Interaction between dispersed phase and dispersion medium?

A solution containing 30 g of non-volatile solute exactly in 90 g of water has a vapour pressure of 2.8 kPa at 298 K. Further, 18 g of water is then added to the solution and the new vapour pressure becomes 2.9 kPa at 298 K. Calculate:

1) Molar mass of the solute

2) Vapour pressure of water at 298 K.

Why are Mn²⁺compounds more stable than Fe²⁺ towards oxidation to their +3 state?

Define the following terms:

(i) Mole fraction    (ii) Molality    (iii) Molarity   (iv) Mass percentage.

Give examples and suggest reasons for the following features of the transition metal chemistry:

(i)The lowest oxide of transition metal is basic, the highest is amphoteric/acidic.

(ii)A transition metal exhibits highest oxidation state in oxides and fluorides.

(iii) The highest oxidation state is exhibited in oxoanions of a metal.

Calculate the 'spin only' magnetic moment of M²⁺_(aq) ion (Z = 27).

What is the role of depressant in froth floatation process?

Which is a stronger reducing agent Cr²⁺ or Fe²⁺ and why?

Describe a method for refining nickel.